Pathway DMX Relay Controller (programmable) - # LCRC48GEP Manuel d'utilisateur télécharger pdf

LCRC48GEP DMX RELAYCONTROLLER Configuration

INSTALLATION INSTRUCTIONS

1 -

Ensure that relay panel power is off (no indicator LEDs

glowing on the system motherboard). Remove the metal

cardframe cover.

2 -

Connect the DMX data line at the panel motherboard, with D-

to the black terminal and D+ to the red terminal. Attach the

shield drain wire to the SHIELD terminal.

3 -

If the DMX line is to be passed through to another panel,

attach the outgoing wires to the second set of data terminals.

4 -

If the relay panel is the last panel on the DMX wire run, it is

recommended that a 100 or 120 ohm 1/4W termination

resistor be installed between one pair of black and red data

line terminals.

5 -

Connect switch wiring to the A/B master switch input terminals

as required. The white terminal is switch common, the red is

switch "on", and black is switch "off". Connect the pilot lamp to

the yellow terminal adjacent to the first of the assigned relays.

6 -

Plug the controller card and one to four LCRD-12 driver cards

firmly into the cardframe.

7 -

Configure the controller card according to the following DIP

switch settings. Restore power.

8 -

Check that the power LED (between the DIP switch and the

three rotary switches) is glowing steadily. This indicates +5

volts present and correct microprocessor operation. A flashing

LED indicates a defective controller card.

9 -

Follow the program mode instructions to program the card for

optional DMX patch assignment and panel master switch

inputs.

10-

Apply the DMX control signal and observe that the receive

data LED (at left) is glowing. The LED will not glow if the

address set on the rotary switches exceeds either 512 or the

number of dimmer signals present on the data line, if the data

format does not conform to USITT-DMX512, or if the data

wires are reversed at the mother board.

11-

Verify relay operation with the DMX control system or the

card's test function, then use the checklist to ensure that

everything is set correctly before re-installing the cardframe

cover.

THRESHOLD SELECT DS-1

25% THRESHOLD (Trigger on at 30%, off at 20%) ON

75% THRESHOLD (Trigger on at 80%, off at 70%)

OFF

STATUS QUO

DS-2

ON (INFINITE HOLD) ON

OFF (2 SECOND HOLD) OFF

RELAY SELECTION DS-3 DS-4

1-12 RELAYS INSTALLED

ON ON

13-24 RELAYS INSTALLED

OFF ON

25-36 RELAYS INSTALLED ON OFF

37-48 RELAYS INSTALLED OFF OFF

CONTROL MODE DS-5

PATCH

Addressing determined by programmed patch for

each relay

OFFSET

Panel start address determined by the address

select switches

OFF

SCAN RATE

DS-6

FAST SCAN (50 msec., 20 relays per second)

NORMAL SCAN (100 mseC., 10 relays per second)

OFF

DIP Switch Settings

3.7"

10.3"

JP1

OPEN POSI TI ON SHOWN

Rx D

x100 x10 x1

PWR

ADDRESS SELECT

RELAY SELECT PROGRAM

ON = D OWN

PGM TST

x10

PROGRAM MODE

DS-7

Program Mode Enabled

Program Mode Disabled (RUN MODE)

OFF

TEST MODE DS-8

Test Mode enabled

Normal (RUN) Mode

OFF

1 2

Résumé du contenu

Page 1 - DIP Switch Settings

LCRC48GEP DMX RELAYCONTROLLER Configuration INSTALLATION INSTRUCTIONS 1 - Ensure that relay panel power is off (no indicator LEDs glowing

Page 2 - Configuration

LCRC-48GEP DMX RELAY CONTROLLER Configuration NOTES ON DMX OPERATION When a DMX signal is used to control relays, on or off operation occurs as

Commentaires sur ces manuels

Pas de commentaire

Pathway DMX Relay Controller (programmable) - # LCRC48GEP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Relais Pathway DMX Relay Controller (programmable) - # LCRC48GEP. Pathway DMX Relay Controller (programmable) - # LCRC48GEP User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Relais Pathway DMX Relay Controller (programmable) - # LCRC48GEP